sad to see our planet in another few hundred years. We need to start preserving our environment, and not drilling our Great Lakes for oil is a great place to start. If we drill for oil, we will lose much wildlife, destroy habitats, have possible oil spills, and in fact endanger ourselves in the long run. To extract such oil from under the Great Lakes, we would need to use directional drilling. To do this, the well is first drilled vertically, and then it is angled under the lakes at about four thousand
offered to reduce our nation's dependence on foreign countries for oil has been opening up drilling in the Arctic National Wildlife Refuge (ANWR). Proponents say that drilling in ANWR would make the United States more self-sufficient in the area of energy, while at the same time not doing excessive damage to the environment of the area. Opponents of drilling in ANWR cite the environmental problems of off-shore drilling and maintain that this land should be left alone and allowed to stand as an environmental
form of drilling that we have today. Fracking is the use of sand, water, and chemicals injected at high pressures to blast open shale rock and release the trapped gas inside. Still, many debate the use of fracking because while it provides jobs and helps the economy, fracking is awful for the environment because it uses many chemicals in the drilling process and it contaminates large supplies of drinking water. Fracking is a fairly new drilling technique that uses a form of horizontal drilling through
Marcellus Shale drilling causes a problem because it involves the use of hundreds of deadly chemicals. Over three hundred chemicals are used in the Marcellus Shale drilling process (Environmental). According to Howells, author of the article “Don’t Frack with Our Water!,” these chemicals are especially dangerous because the companies that use them will not tell the public what specific chemicals are being used. However, through studies of the chemicals, some of them can be identified. Some of the
For more than a decade, debate over drilling for oil on the Coastal Plain of the Arctic National Wildlife Refuge [ANWR] has continued unabated. The proposal to drill for oil in Arctic National Wildlife Refuge is heavily urged by the oil companies and supported by most Alaskan government officials, has drawn full scale opposition from powerful private environmental organizations representing millions of members throughout the United States. Congress established the Arctic National Wildlife Refuge
First of all, what in the world is coiled tubing? Otherwise referred to as CT, coiled tubing is a manufactured product used in field operations such as well service, workover applications (petroleum industry well work), and drilling and completion applications. Just as is sounds, CT is essentially a continuous tube with a diameter of .75 inches up to 4.5 inches that is reeled onto a spool, which has a core diameter of approximately eight to twelve feet. The tubing is made from rolling strip metal
drill offshore. The reason that we drill offshore is because approximately one third of the world's oil resides in offshore fields. (Lynch, 213) There are many ways to drill oil from the ocean floor. The most common way is to construct a steel drilling platform on the ocean floor. Other ways are, first a jack-up rig which is used in waters of up to 200 feet. The rig rests on a floating platform attached to steel legs that can be jacked up or down. It is moved by workers lowering the platform
Drilling holes is something most of us have done, whether as part of a hobby, or for our jobs. One of the basic tools for the homeowner, the handyman, or a contractor is an electric drill. While hand-held power drills are some of the most used tools in the box, they are not necessarily the most accurate. When you need an exact hole drilled at a precise angle, or maybe a hundred of these holes, then the tool you want is a Drill Press. The drill press is a larger version of a hand drill with additional
construction workers may be easily exposed to respirable crystalline silica during activities such as the following: · Chipping, hammering, and drilling of rock · Crushing, loading, hauling, and dumping of rock · Abrasive blasting using silica sand as the abrasive · Abrasive blasting of concrete (regardless of abrasive used) · Sawing, hammering, drilling, grinding, and chipping of concrete or masonry · Demolition of concrete and masonry structures · Dry sweeping or pressurized air
The principle of cable-tool drilling has remained unchanged since it first started in China. According to Kurts, DeGolyer (1940) “Drilling is done by repeatedly lifting and dropping a heavy string of drilling tool into the borehole, with the drill bit crushing consolidated rocks into small fragments”. Huge improvements have been made from the Chinese bamboo method. University of Kansas (1940) highlighted the key improvements that the rig mechanisms had. A good example of this is the spring pole
Why I chose offshore Drilling? I chose offshore drilling, because I recently saw the movie trailer of Deepwater Horizon, where a drilling oil rig fails, and the oil that is being pumped spills into the water, and the oil gets caught of fire, a lot of people, and sea animals become endangered. I don’t know what about this movie, all I know is that I always find myself thinking about what I would do it I was on the rig. With Offshore drilling being an option that I could research about, I wanted to
Q3 2011 was 38.1 million, an increase of 9% compared to the prior quarter. This increase derived from increase customer demand for shale resources. Casing Drilling revenue Q3 2011 was 5.3 million compared to 3.9 million in Q2011. • Top drive operating margi... ... middle of paper ... ...13, the company acquired automated catwalk technology from Custom Pipe Handlers Canada, Inc. (nytimes.com, 2014). 4.2.4 Summary of Tesco Resources and Capabilities In summary, Tesco Corporation has strong
The Ocean Ranger The Ocean Ranger was an offshore exploration oil drilling platform that sank in Canadian waters 315 kilometres southeast from St. John's Newfoundland, on the Grand Banks of Newfoundland on February 15, 1982, with 84 crewmembers onboard. The Ocean Ranger was the largest semi-submersible, offshore exploration, oil drilling platform of the day. Built in 1976 by Japan's Mitsubishi Heavy Industries, it operated off the coasts of Alaska, New Jersey, Ireland, and in November 1980 moved
economics, geology, geochemistry, geomechanics, geophysics, oil drilling, geopolitics, knowledge management, seismology, team building, teamwork, tectonics, thermodynamics, well logging, well completion, oil and gas production, reservoir development, and pipelining. A petroleum engineer must acquire knowledge in areas which include petrophysics, drilling and product operations, reservoir engineering, production geology, production technology, field development economics and of course a lot of math with
that ancient China had some of the most influential ‘thinkers’ of that period who helped to shape their world. The early Chinese left behind a great number of legacies which were the forerunners to the ideas and technologies we enjoy today such as basic medicine, paper currency, deep drilling and the bureaucracy system. For the ancient Chinese, most of their knowledge of early Chinese medicine was obtained from the yellow emperor’s Nei Ching. This is believed to have been from the 2nd century BC
BP being the source of the disaster did not make any attempts to repair the equipment on the drilling rig as it would cost them time and money to take care of it. First of all being on a drilling rig even one that well maintained will have some risk involved whether it be equipment failing and causing injury or something else, but knowing that your rig needs 390 major repairs and not doing anything
drawings given by the Consultant. The surveying details for each location should include the reduced levels and coordinates. The place that is surveyed and marked as the pile position shall not be disturbed prior to the commencement of boring works. DRILLING All the associated technical information such as presence of services, pile coordinates, platform and cut-off levels, validity of drawings etc need to be verified by the client's representative to begin the operations. If needed, after setting up
Introduction: The drilling machine/drill press has been utilized to create the holes. Drilling is basically used to produce holes with the application of tool drill named as drill bit. The drill bit is a cylindrical bar having helical flutes and radial cutting edges at one end. The drilling operation may be defined as the rotation of drill and feeding it into the work piece being drilled at a specified speed and feed as per the necessity varying to the size and depth of the hole. The process is
certain that the exploration and production of petroleum from deep-water formations would not incur any sort of environmental damages. Several decades later, scientists learned new information from monitoring programs and research studies that offshore drilling did cause effects on the health of benthic organisms and other marine fauna in the proximity of offshore platform rigs. This paper studies the consequences of offshore platform rigs on marine organisms and wildlife from the perspectives of what
The Chilean mining accident The recent 2010 Copiapó mining accident, to us known as the Chilean mining accident began on 5th of August 2010 as a large collapse at the San José copper-gold mine in the Atacama Desert. During the collapse there were thirty three men inside the mine; trapped 700 meters underground; five kilometers from the entrance. It is not surprising that the public thought that the miners would not have survived the collapse or starve to death. Thou it sounds like there is no