CHAPTER 3
EXPERIMENTAL DETAIL
3.1 PVC MODELS
3.1.1 FABRICATION OF PVC PIPE STEAM BATH
The description of Items used in making PVC Pipe Steam Bath and their quantity is mentioned in Table 3.1. As shown below, we need 23 Feet long PVC pipe and 16 PVC fitting (L & T shape joint), Soft and crack resistant polythene and wooden steam hose.
Table 3.1: Bill of material for PVC Pipe Steam Bath
Item Description Description
01 PVC pipe 23 Feet
02 PVC Fitting 16 (L & T-joint)
03 Soft and crack resistant polythene 2.5 m
04 Wooden Steam hose 1 Actual & Labelled picture of PVC Pipe Steam Bath is shown in Fig. 3, side and top view of PVC Pipe Steam Bath
…show more content…
6: Systematic Diagram of Steam Bath
3.1.1.2 ADVANTAGES OF PVC PIPE STEAM BATH
PVC Pipe Steam Bath is cost economic. This Steam Bath costs about ₹ 600-700 while the other body steamers available in market costs about ₹ 5000-6000. It is also easy to use and is environmental friendly. It is durable, tough and flame resistant. This Steam Bath uses minimal energy and water consumption. PVC Pipe Steam Bath refreshes the body and mind, deep cleans the skin and moisturizes it. Also helps in releasing daily stress and tension, and relaxes tight overworked muscles. It reduces aches and pains in joints. Revitalizes nasal, sinus and chest congestion.
3.1.2 FABRICATION OF PVC PIPE KID’S SCOOTER
The description of Items used in making PVC pipe Kid’s Scooter and their quantity is mentioned in Table 3.2. As shown below, we need 13 Feet long PVC pipe and 13 PVC fitting (L & T shape joint), 3 wheel, 6 bearing for better handle movement, 1 wheel clamp used for holding the wheel, 1 wood ply, 6 screw and nut to fix the wood ply on the PVC base frame, and 1 adhesive liquid used for join all joints.
Table 3.2: Bill of Material for PVC Pipe Kid’s Scooter
Item Description Quantity
01 PVC pipe 13 feet
02 Wheel
…show more content…
To prepare the PVC Pipe Kid’s Scooter.
2. It suitable for age group 8 to 12.
3. To make the base of the scooter. This step can be further divided into following sub-steps;
a. Making the frame using PVC pipe and fitting the rear wheel in it.
b. Fixing base (plywood of desired dimension) in frame using screw.
c. Attaching the center wheel in wooden base using screw.
4. To make the handle of scooter. This includes fitment of 3 parts, fixing of front wheel (with clamp) and vertical pipe in a T-joint which has bearing in it, so that the whole assembly can be seen as a handle and we can move it in required direction.
5. To join two separate assemblies which we have made in previous steps. I.e. we will attach the handle with the base of the scooter using connecting pipe, screw, nuts and adhesive. Refer fig. 7, fig.8, fig.9, and fig.10 is Actual & Labelled picture, top view, basic structure and making of PVC Pipe Kid’s Scooter.
3.1.2.2 ADVANTAGES OF KID’S SCOOTER
PVC Pipe Kid’s Scooter is cost economic. This PVC Pipe Kid’s Scooter costs about ₹ 600 while the other Kid’s Scooter available in market cost ₹ 1500-2000. It is also easy to use and is environmental friendly. It is durable, tough, corrosion resistant, termite resistant and light weight. It is foldable thus requires very less
Most scooters are younger kids. Do you see more 4 year olds running around on a skateboard or on a razor scooter? That's because you just hop and go on a scooter. They are young, lack tendency for a sustain skatepark effort (Skatepark Development Guide). They are causing accidents or jumping in the way.
To build a ramp or install a chair lift for a person who becomes disabled (to allow him or her to continue living at home).
device used in practicing baseball and came up with the tee. A good tee now a day's cost
During the 1950’s when skateboarding first got it’s legs it was a very popular activity to take part in during vacations to ocean side tourist attractions, or as an activity after surfing. Yet, by 1965, skateboarding had diminished in popularity completely, therefore almost every skateboard manufacturer went out of business. . During this time the only people who even wanted to skateboard were surfers who needed something to ride to practice their surfing while the waves were flat. Due to the fact that there were no skateboards being made or sold, those who wanted to skate had to take it upon them-selves to manufacture their own boards. Using any kind of scrap they could find to build a usable board out of, such as metal scrap pieces or old planks. These determined surfers had to unscrew the trucks and wheels off of roller skates and attach them to the bottom of their boards. And because these kids were from very poor families for the most part, and next to non had jobs of their own, they had to resort to taking the trucks and wheels off the roller skates secretly in the stores. Although.., the clay wheels th...
The ball joint is the most critical part inside the steering system of the car and the suspension system of the car. The lower ball joint is a joint that connects the front of the wheels in the vehicle and the main axle, and allows the wheels to move freely. Due to the movement of the steering linkage, the ball joints are flexible joints, which have the design of a ball and socket. These lower ball joints are always made of hard steel, and the bearing stud and the socket is received inside the steel housing. There are pivot points between the suspensions of the tires that help in supporting the weight of the vehicle.
In larger cities, as the bath of Constantine was located in, the baths tended to draw on the ornate, generally with colonnades, arches, and large domes . The primary materials used would have been of stone, most likely large quantities of marble would be used for decoration on the walls, floor, and columns. A hypothetical citizen would not be entering the baths during the evening, as the baths would generally close at dusk, a citizen would instead arrive earlier in the day. a would most likely find themselves within a changing room called the apodyterium where they would disrobe. After disrobing, the citizen then had a wide selection of destinations which he could select from. Roman Baths being a social gathering provided all manners of entertainment. Depending upon the bath in question, amenities such as libraries, gardens, or lecture halls to name a few. The key portion of the baths however is the baths themselves. Inside the baths there was three primary baths. the citizen would generally transition from the hot bath "Calidarium" to the warm bath "Tepidarium", both of which used a heating system of lighting fires and channeling the hot air through the hypocaust, the area underneath the floor. then finally the citizen would make it to the unheated pool, the frigidarium, which was generally located in the center of the baths. Beyond bathing the citizen would have the ability to work out in the
mean that we will to set up the apparatus in a way that would give us
Bathing a large dog in a bathtub is a test of human endurance equal to the most trying of Olympic events. It is, however, well worth the effort. You will be rewarded in knowing you are helping to keep your pet healthy. Additionally, you will know your home won't smell like the primate building at the zoo.
The concept of public bathing first arose in ancient Greece and later spread to Rome. The earliest Roman baths date back as far as the 4th century BC, and contained little more than a “row of hip-baths.” Originally mixed bathing between men and women was common, however Emperor Hadrian passed a law forbidding it in the second century. As a result, bath complexes had different hours for men and women or “built additional facilities so that both sexes could be accommodated at the same time.” Over time, advances in technology allowed Romans to “improve size and efficiency [of bath houses] and eventually to build the great double-circulation baths (thermae) which combined hot and cold bathing facilities, swimming pools, running tracks, sports grounds, and libraries […].” Bath complexes became so large that they could...
UK shower market had (has?) a big potential, since only 60 percent haven’t had a shower. Many homes still had archaic, gravity based plumbing and cold water tank or cistern on the roof. Separate boiler and cylinder were needed to store hot water in a nearby airing cupboard. Sound like a good opportunity.
It is essential to know how to use a hot tub in order to protect your health
In the United States, a massive quantity of homeowners only have a bath tub in their houses. Most bath tubs truly are not just bathtubs; numerous also double as showers. As good as it's to only have one bathroom fixture, in particular one which could do two jobs, you might be on the lookout for a lot more. Should you be looking to remodel your bathroom, you may would like to take into consideration purchasing your self a new bathtub. Sad to say, you will get that not all bath tubs double as showers; for this reason, you could also be inside the market for a new shower stall.
The list of Apparatuses and materials used and how to setup them can be found in appendices. (Appendix 2)
turbine via interceptor valves and control valves and after expanding enters the L.P. turbine stage via 2 numbers of cross over pipes. In the L.P. stage the steam expands in axially opposite direction to counteract the trust and enters the condenser placed directly below the L.P. turbine. The cooling water flowing throughout the condenser tubes condenses the steam and the condensate collected in the hot well of the condenser. The condensate collected is pumped by means of 3*50% duty condensate pumps through L.P. heaters to deaerator from where the boiler feed pump delivers the water to boiler through H.P. heaters thus forming a closed