Wait a second!
More handpicked essays just for you.
More handpicked essays just for you.
Test
Test
Don’t take our word for it - see why 10 million students trust us with their essay needs.
Recommended: Test
A. Sample and Hold circuit The main function of sample and hold circuit is to sample the input signal. The sampling frequency of the circuit should be follow by nyquist criteria of the sampling theorem. B. Analog to Digital converter Analog and Digital converter is used to convert the analog signal into digital sequence. The analog to digital converter took the instantaneous analog voltage value from the sample and hold circuit and converts it to the appropriate digital sequence depending the reference voltage. The AVR ATmega 8 has an a inbuilt ADC in microcontroller. C. USART USART stands for universal Synchronous Asynchronous Receiver transmitter. It is sometimes called the serial communication interface or SCI. …show more content…
RS232 connector In telecommunication RS232 is a standard for serial communication transmission of data . it formally defines the signal connecting between DTE(data terminal equipment) such as a computer terminal, and DCE(data circuit terminating equipment) such as a modem. The RS232 standard commonly used in computer serial ports.[3] When we connect the RS232 connector cable to the computer. The operating system of the computer assigns a port number to the RS232 port. These port number used in the programing to identify the data from coming serial port. The Baud rate of DAQ device an computer is must be …show more content…
23 programmable I/O lines 2. 28 pin PDIP o Peripheral Features 1. Two 8-bit Timer/Counters with Separate Prescaler and Compare Mode 2. One 16-bit Timer/Counter with Separate Prescaler, Compare Mode, and Capture Mode 3. Real Time Counter with Separate Oscillator 4. Six PWM Channels 5. Programmable Serial USART 6. Interrupt and Wake-up on Pin Change AVR ATmega 8 comes with on chip analog to digital converter and USART module. For storing the embedded program the AVR microcontroller comes with an 8k on chip flash program memory. The Baud rate of an USART can be adjust using a program. We have to program it according to our requirement.[2] V. RESULT The result of the output of LABView shown in figure 4.These shows that the DAQ device worked satisfactory. It works for temperature monitoring and level monitoring. VI. CONCLUSION A low cost DAQ system device has been implemented and tested. It gives satisfactory response. These device can be used in for various application at collage level as well as industry level. The Daq device can used in biomedical also. these and shows the output. Snapshot of an output shown by labview is showed in following
I have to pull two alleles (two straws) from the bag to represent one fish because fishes like humans get two alleles one from their father and one from their mother.
The results of this experiment are shown in the compiled student data in Table 1 below.
In order to further improve the accuracy of the experiment, I will use a sound recorder which has
We must first begin the today’s lab by connecting the thermometer that digitally detects surrounding temperature to the Lab Pro Interface located on the computer via...
The data and information I have collected is directly from the team of Australian Hardware team so this information is valid enough to be used for research of the given
Oscilloscope is acquainted as one of the most helpful instrument for testing circuits. It is able to show the signals at different points in the circuit. One way to inves...
how this tool can be used with more advanced technologies in the future. The following
Network cables are another component that is used in communication between network devices. Cables are used to connect one network device to other via several different connections. The most reliable type of connection between two or more devices is to use a wired connection. These connections can be used to share data and access between servers, PCs, printer...
There are a great number of applications for Digital Signal Processing and in order to better understand why DSP has such a large impact on multiple aspects of society, it helps to better understand the wide variety of applications it can be used for. Here we will briefly look into the following applications of Digital Signal Processing and their uses; speech and audio compression, communications, biomedical signal processing and applications in the automobile manufacturing industry. Li Tan [1] goes into detail with each of these applications in his book, Digital Signal Processing, and explains how each are used on a daily basis.
In telecommunication, serial transmission is the sequential transmission of the signal elements of a group representing a character or other entity of data. The characters are transmitted in a sequence over a single line, rather than simultaneously over two or more lines, as in parallel transmission. The sequential elements may be transmitted with or without interruption.
In today’s technologically advanced environment, computers are everywhere. Electronic devices are in incorporated into our lives from the mirrors in our bathroom to the smart phones in our pockets and everything in between. The vision of Andrews, Inc is “To be the manufacturer’s choice for sensors, powering the things of everyday life.” Our goal is to build sensors which are adequate, affordable and accessible to the business customers building the products of today. The Andrews business customer is looking for sensors which will get the job done. Put another way, they are need a basic sensor designed to meet their product needs. Our customers are looking for ways to increase their contribution margins and maintain a reasonable price point for their consumers. Lastly, these business customers need the product to meet their production schedule. It is essential to be a key supplies contributing to the customers value chain activities.
2. To transfer files from one computer to another (the files may be text, images, audio, video, etc.).
When electronic devices transfer information to another electronic device, the devices need to know when data flow is beginning and ending. This is done with signals for synchronization.i
Does the proposed equipment have the technical capabilities to hold the data which is required to use the new system?
The TCP/IP is the most important internet operation protocol in the world. While IP protocol performs the mass of the functions which is needed for the internet to work. It does not have many capabilities which are essential and needed by applications. In TCP/IP model these tasks are performed by a pair of protocols that operate at the transport layer. The Transmission Control Protocol (TCP) and the User Datagram Protocol (UDP). These two protocols are vital when it comes to delivering and managing the communication of numerous applications. To pass on data streams to the proper applications the Transport layer must identify the target application. First, to be able to attain this, Transport layer assigns an application an identifier. In the TCP/IP model call this identifier a port number. Every individual software process needing to access the network is assigned a un...