Essay Color Key

Free Essays
Unrated Essays
Better Essays
Stronger Essays
Powerful Essays
Term Papers
Research Papers




System Boot Sequence

Rate This Paper:

Length: 1011 words (2.9 double-spaced pages)
Rating: Red (FREE)      
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

System Boot Sequence
The system BIOS is what starts the computer running when you turn it on. The following are the steps that a typical boot sequence involves. Of course this will vary by the manufacturer of your hardware, BIOS, etc., and especially by what peripherals you have in the PC. Here is what generally happens when you turn on your system power:
1. The internal power supply turns on and initializes. The power supply takes some time until it can generate reliable power for the rest of the computer, and having it turn on prematurely could potentially lead to damage. Therefore, the chipset will generate a reset signal to the processor (the same as if you held the reset button down for a while on your case) until it receives the Power Good signal from the power supply.
2. When the reset button is released, the processor will be ready to start executing. When the processor first starts up, it is suffering from amnesia; there is nothing at all in the memory to execute. Of course processor makers know this will happen, so they pre-program the processor to always look at the same place in the system BIOS ROM for the start of the BIOS boot program. This is normally location FFFF0h, right at the end of the system memory. They put it there so that the size of the ROM can be changed without creating compatibility problems. Since there are only 16 bytes left from there to the end of conventional memory, this location just contains a "jump" instruction telling the processor where to go to find the real BIOS startup program.
3. The BIOS performs the power-on self test (POST). If there are any fatal errors, the boot process stops. POST beep codes can be found in this area of the Troubleshooting Expert.
4. The BIOS looks for the video card. In particular, it looks for the video card's built in BIOS program and runs it. This BIOS is normally found at location C000h in memory. The system BIOS executes the video card BIOS, which initializes the video card. Most modern cards will display information on the screen about the video card. (This is why on a modern PC you usually see something on the screen about the video card before you see the messages from the system BIOS itself).
5. The BIOS then looks for other devices' ROMs to see if any of them have BIOSes. Normally, the IDE/ATA hard disk BIOS will be found at C8000h and executed. If any other device BIOSes are found, they are executed as well.
6. The BIOS displays its startup screen.
7. The BIOS does more tests on the system, including the memory count-up test which you see on the screen. The BIOS will generally display a text error message on the screen if it encounters an error at this point; these error messages and their explanations can be found in this part of the Troubleshooting Expert.
8. The BIOS performs a "system inventory" of sorts, doing more tests to determine what sort of hardware is in the system. Modern BIOSes have many automatic settings and will determine memory timing (for example) based on what kind of memory it finds. Many BIOSes can also dynamically set hard drive parameters and access modes, and will determine these at roughly this time. Some will display a message on the screen for each drive they detect and configure this way. The BIOS will also now search for and label logical devices (COM and LPT ports).
9. If the BIOS supports the Plug and Play standard, it will detect and configure Plug and Play devices at this time and display a message on the screen for each one it finds. See here for more details on how PnP detects devices and assigns resources.
10. The BIOS will display a summary screen about your system's configuration. Checking this page of data can be helpful in diagnosing setup problems, although it can be hard to see because sometimes it flashes on the screen very quickly before scrolling off the top.
11. The BIOS begins the search for a drive to boot from. Most modern BIOSes contain a setting that controls if the system should first try to boot from the floppy disk (A:) or first try the hard disk (C:). Some BIOSes will even let you boot from your CD-ROM drive or other devices, depending on the boot sequence BIOS setting.
12. Having identified its target boot drive, the BIOS looks for boot information to start the operating system boot process. If it is searching a hard disk, it looks for a master boot record at cylinder 0, head 0, sector 1 (the first sector on the disk); if it is searching a floppy disk, it looks at the same address on the floppy disk for a volume boot sector.
13. If it finds what it is looking for, the BIOS starts the process of booting the operating system, using the information in the boot sector. At this point, the code in the boot sector takes over from the BIOS. The DOS boot process is described in detail here. If the first device that the system tries (floppy, hard disk, etc.) is not found, the BIOS will then try the next device in the boot sequence, and continue until it finds a bootable device.
14. If no boot device at all can be found, the system will normally display an error message and then freeze up the system. What the error message is depends entirely on the BIOS, and can be anything from the rather clear "No boot device available" to the very cryptic "NO ROM BASIC - SYSTEM HALTED". This will also happen if you have a bootable hard disk partition but forget to set it active.
This process is called a "cold boot" (since the machine was off, or cold, when it started). A "warm boot" is the same thing except it occurs when the machine is rebooted using {Ctrl}+{Alt}+{Delete} or similar. In this case the POST is skipped and the boot process continues roughly at step 8 above.

How to Cite this Page

MLA Citation:
"System Boot Sequence." 123HelpMe.com. 28 Nov 2014
    <http://www.123HelpMe.com/view.asp?id=159541>.


Related Searches





Important Note: If you'd like to save a copy of the paper on your computer, you can COPY and PASTE it into your word processor. Please, follow these steps to do that in Windows:

1. Select the text of the paper with the mouse and press Ctrl+C.
2. Open your word processor and press Ctrl+V.

Company's Liability

123HelpMe.com (the "Web Site") is produced by the "Company". The contents of this Web Site, such as text, graphics, images, audio, video and all other material ("Material"), are protected by copyright under both United States and foreign laws. The Company makes no representations about the accuracy, reliability, completeness, or timeliness of the Material or about the results to be obtained from using the Material. You expressly agree that any use of the Material is entirely at your own risk. Most of the Material on the Web Site is provided and maintained by third parties. This third party Material may not be screened by the Company prior to its inclusion on the Web Site. You expressly agree that the Company is not liable or responsible for any defamatory, offensive, or illegal conduct of other subscribers or third parties.

The Materials are provided on an as-is basis without warranty express or implied. The Company and its suppliers and affiliates disclaim all warranties, including the warranty of non-infringement of proprietary or third party rights, and the warranty of fitness for a particular purpose. The Company and its suppliers make no warranties as to the accuracy, reliability, completeness, or timeliness of the material, services, text, graphics and links.

For a complete statement of the Terms of Service, please see our website. By obtaining these materials you agree to abide by the terms herein, by our Terms of Service as posted on the website and any and all alterations, revisions and amendments thereto.



Return to 123HelpMe.com

Copyright © 2000-2014 123HelpMe.com. All rights reserved. Terms of Service