Safety
Handling material by hand
The insulated panels, while not particularly heavy, can be awkward to handle and carry, and the wind can catch them. Use good lifting techniques and body position when you lift or move the panels. Installation often requires working at unusual angles while accessing duct systems.
Eye protection
Making minor modifications to the panel system or routing out for the insulation can create airborne dust and particulates. Wear safety glasses with side shields (Z87-1). In windy conditions, you might need to wear mono-goggles for additional protection. Beware of sunlight reflecting off the aluminum surfaces—wearing tinted safety glasses is a good idea.
Hand safety
The aluminum foil edges of the panels are sharp (yes, that foil can cut you), and sharp corners and edges are common on ductwork. At a minimum, wear sturdy leather gloves while handling the material. Even better, wear cut-resistant gloves, such as Kevlar® or equivalent.
Tool safety
Be sure knife blades are sharp, electrical cords are undamaged, and tools are in overall good condition. Don’t use damaged tools. Use the right tool for the job.
Electrical safety
Wherever necessary, participate in the Lock, Tag, Test, and Try process for energized equipment. Verify lockout locations and make sure your personal control lock is installed at the correct spots. Most installations are performed outdoors in possibly wet conditions. When working in these areas with electrical tools, use ground fault circuit interrupters.
Environmental conditions
Plan for the unexpected. Be paranoid! Thoroughly inspect your job area to find hazards. Look for pinch points, trip hazards, energized sources, and other suspicious conditions. Find them ahead of time and eliminate them before you start your work.
Flat Stock
Store the sheet metal flat, preferably on a shelf near the work surface so you can slide the sheet onto the work surface without kinking the sheet.
You can store the insulation sheets either flat or on edge. In both cases, take care not to dent the edges and corners.
Develop a system for storing and keeping track of the supplies and equipment. Keep enough on hand so you don’t run out.
Storage
The raw materials and finished Techna-Duc® should be stored inside, away from condensing moisture, while awaiting fabrication and field installation.
Keep the aluminum sheets dry. Moisture trapped between the sheets creates ugly black stains that cannot be removed. The stains do not weaken the product, but they are undesirable. If possible, arrange your shop so you can slide sheets one at a time directly onto the work surface.
If you are concerned about safety, then consider the low height and transparent mesh side windows. The windows help ensure ventilation and airflow.
...nd others for injuries, look for and extinguish small fires, inspect your home for damage, listen to the radio for instructions, and expect aftershocks.
Ensure that all necessary earth connectors are then attached to the isolation points and any overhead wires
4) Be aware of static sparks. Do not use metal instruments to mix or grind materials.
First, while barehanding there is a suit that consist of wearing a protective wear while the wire is energized the suit is made up of specialized boots, protective socks with interwoven microscopic stainless steel fibers, in addition to a hard hat. The $1,300 suit comes with boots that have a conductive sole, a jumper, a hooded shirt, gloves, and socks.. Linemen wear flame-retardant clothing which includes hooded sweatshirts, long-sleeved shirts, pants, winter clothing, and overalls. One well-known distributor that makes this clothing is Carhart. Also, lineman are required to wear safety glasses, steel-toed boots, leather gloves and proper safety gear. The proper safety gear can include equipment such as flame-retardant harnesses. On a daily basis the linemen inspect all of their perso...
Aluminum is slightly hazardous in case of skin contact (irritant), non-hazardous in case of ingestion, and non-hazardous in case of inhalation.
How they store the box is kind of like sweeping it under the covers, they just hide it away out of sight and out of mind until the
Establish a change management process. All the changes need to be documented for the reference of other team members.
Provide other means of ventilation like windows if it’s not safe to use the inbuilt ventilation systems.
If I wanted to cut a piece of paper that had three invoice slips on it into separate pieces, I would first look for a pair of scissors, as they are relatively safe and appropriate for the task. However if there are no scissors available, I may instead opt to use a ruler to tear the paper instead, as although it is not the most appropriate tool for the task, in the situation it would be time and cost effective. It also doesn’t matter too much if the edges are jagged on an invoice slip. If I had to cut something in a more presentable way I may have to take the less efficient option and check with another department to see if they had scissors I could use.
I also wear a high-vis vest on site to make myself more noticeable to anyone working nearby. I also wear protective gloves, as I am cutting tiles the edges can be quite sharp and could cut my hands/fingers so in this case I use gloves to prevent this from happening. I wear steel toe cap boots which are the right size and comfortable to prevent hurting my feet/toes. As a tiler carrying heavy boxes of tiles around to different locations there is a chance I could drop them and without steel toe cap boots on they can possibly break your toes or in other cases your foot. I wear a hard hat adjusted to the right size, which is perfect for the job and not worn out to prevent hurting my head from falling from above.
Leather Gloves: These kinds of gloves are used to protect hands while working with fire, and rough surfaces. The leather gloves are also used in combination with insulated liners while working with the electricity.
There are sometime thing that even you can’t accomplish be yourself, If you know you can't do something ask someone else for help when working as an electrician. Safety is the most important thing that is needed when being an electrician and working with electricity. When asking for help your co-workers will help you, because you help each thought out the whole project. That is friendship that is alway needed in a job.Safety is the first priority that is needed to be followed without anyone telling you. Don’t joke around when you are working near electricity. You should be serious in willing to help when you are needed or when you need help.
I would ensure subsequent monitoring and evaluations of the program by keeping files and using strategies.
To begin with, the first type of hazard/exposure is fire and explosion. Fire is highly flammable and the vapor is heavier than normal air. It can travel for a considerable distance to source of ignition and flash back. Fire can be of 3 types: small, large and fire involving tanks or cars or trailer loads. An acute hazard can be the vapor/air mixtures that cause explosions. One way of preventing is to not open flames and sparks as well as no smoking. It is also preferable to take off reactions in clo...